View cart
Shopping cart is empty.
Phone Lyndons hardwaer suppies

LOCATE YOUR NEAREST STORE

Phone, fax or shop online

 

Easymix - Riversands

This catalog has no sub-catalogs.
  • {
      "moduleName": "tag_productlist_3",
      "description": "Easy Mix Concrete 30KG
    \n

    Easy Mix Concrete is a convenient, pre-blended mix of dry\naggregates, specially graded sands and cement that achieves a fully\ncured strength rating of 25MPa.

    \n

    It is ideal for applications that require a smooth, quality finish such as small slabs, paths, footings and garden edges but can also be used for securing letterboxes, fence posts, light posts and clothes lines.

    \n

    Now available in our all new weather resistant water proof packaging.

    \nApplication
    \n
    \n
    \n
      \n
    1. Make sure your project is properly laid out with all the necessary tools at hand.
    2. \n
    3. Pour the requires volume of concrete into a wheelbarrow or onto a\n clean surface. Use contents as soon as possible after opening the\n package.
    4. \n
    5. Calculate the amount of water you will need. As an approximate guide,\n use 1.0 – 1.2 litres of clean water per 10kg bag, 2.0 – 2.3 litres of\n water per 20kg bag and 3.0 – 3.5 litres per 30kg bag.
    6. \n
    7. Add water gradually and mix thoroughly to a stiff consistency. Do\n not add water after the concrete has been mixed, as this will reduce the\n strength of the concrete.
    8. \n
    \n

    Note: Excess water can ruin good concrete, use caution when adding water to your mix.

    \n
    \n
    \n Handy Hints
    \n
    \n
    \n

    Placing Concrete

    \n
      \n
    1. Using a straight-edge board across the top of the formwork, ‘screed’\n the concrete to the desired level. Work the screedboard across the slab\n from one end to the other in a sawing motion to bring the slab to its\n finished level.
    2. \n
    3. Fill any holes and screed again.
    4. \n
    5. Remove excess concrete if necessary and leave the slab to set for 1 hour (depending on weather conditions), before finishing.
    6. \n
    \n

    \n

    Finishing Concrete
    \n
    Leave the installed concrete to stand for approximately one hour before trowling to the desired finish.

    \n

    For a non-slip finish (or if tiling over top), use a wooden float in a\ncircular motion across the slab. For a smooth finish, a steel float\nshould be used. Edges should be finished with an edging tool for best\nresults.

    \n

     

    \n

    Curing Concrete
    \n
    Cure the concrete by keeping it moist for 7 days.

    \n
    \n
    ", "catalogId": 297339, "id": 10053475, "name": "Easy Mix Concrete 30KG", "url": "/brands-1/easymix-riversands/easy-mix-concrete-30kg", "title": "Easy Mix Concrete 30KG | Lyndons Qld", "smallImage": "/images/hardware/small/easy_mix_concrete.jpg", "smallImageUrl": "/images/hardware/small/easy_mix_concrete.jpg", "largeImage": "/images/hardware/easy_mix_concrete.jpg", "largeImageUrl": "/images/hardware/easy_mix_concrete.jpg", "releaseDate": "2000-01-01T00:00:00", "expiryDate": "9999-01-01T00:00:00", "productCode": "CMNT030", "inStock": null, "onOrder": 0, "reorder": null, "minUnits": 1, "maxUnits": null, "unitType": "Each", "tags": "", "custom1": "Easymix-Riversands", "custom2": "", "custom3": "", "custom4": "", "isOnSale": false, "countryCode": "AU", "currencyFormat": "$", "countryCurrencyFormat": "AUD", "retailPrice": null, "salePrice": null, "wholesalePrice": null, "discountPrice": null, "totalDiscountPrice": null, "totalPrice": null, "tax": null, "taxCode": null, "taxRate": null, "urlWithHost": "http://www.lyndons.com.au/brands-1/easymix-riversands/easy-mix-concrete-30kg", "globals": { "get": { "CatalogueID": "297339" }, "cookie": { "visitorDeviceClass": "desktop", "ASP.NET_SessionId": "qrlmamc2xck5zsthpqzc3wiq", "ANONID_FS2040121": "20.07.2017 18:35:25.639", "ANONID2040121": "d58d5440-18f5-4d75-83ea-8cd32dea9d3d", "VISID2040121": "b587b63d-26fc-4a1c-8eac-fe51abf97521#www.lyndons.com.au#20.07.2017 18:35:25.639" }, "site": { "id": 2040121, "name": "Lyndons", "host": "www.lyndons.com.au", "countryCode": "AU", "language": "EN", "dateNow": "2017-07-21T04:35:25.7202399" }, "visitor": { "deviceClass": "desktop", "ip": "23.20.193.33", "country": "US", "city": "Ashburn", "userAgent": "CCBot/2.0 (http://commoncrawl.org/faq/)", "referrer": "/" }, "cart": { "cartUrl": "/OrderRetrievev2.aspx?CatalogueID=297339" }, "user": { "entityId": 0, "firstname": "", "middleName": "", "lastname": "", "fullname": "", "username": "", "email": "", "email2": "", "email3": "", "customerType": {}, "leadSourceType": {}, "industryType": {}, "ratingType": {}, "isWholesaler": false, "isLoggedIn": false } } }

    Easy Mix Concrete 30KG

    Easy Mix Concrete 30KG

    Part No.
    CMNT030
    Manuf No.
    Easymix-Riversands
    Pack Size
    Each

    per Each

    Qty sought:
  • {
      "moduleName": "tag_productlist_3",
      "description": "Easy Mix Mortar Mix 30KG 
    \n

    Easy Mix Mortar is a pre-blended, superior quality mortar mix\nspecifically designed for both the professional tradesperson and the\nDIY home handyperson.

    \n

    Providing excellent workability characteristics, Easy Mix Mortar is\nsuitable for all brickwork, blockwork and stone laying needs. Typical\nuses include brick or block barbecues and letterboxes, paving, retaining\nwalls, garden beds, and fixing toilet pans and associated pipes.

    \n

    Now available in our all new weather resistant water proof packaging.

    \nMixing\n
    \n
    \n
    \n
    \n
    \n
      \n
    1. Make sure your project is properly laid out with all the necessary tools at hand.
    2. \n
    3. Pour the required amount of Easy Mix Mortar into a wheel barrow or a\n clean bucket. Ensure you use contents as soon as possible after opening\n the product packaging.
    4. \n
    5. Calculate the amount of water you will need. For each 10kg of Mortar add 1.6 litres of water.
    6. \n
    7. Add water gradually and mix thoroughly to a stiff consistency (e.g.\n until the mix just slips off the trowel when lightly flicked). Note:\n Excess water can ruin good mortar. Should too much water be added,\n leave the mixture aside until it thickens to a workable consistency.
    8. \n
    9. The mortar is now ready to trowel onto bricks or blocks.
    10. \n
    \n

    Note: To improve the workability of cement mortar, we recommend Easy\nMix Mortar Aid an easy to use liquid that enables quicker application\nand reduces cracking.

    \n

    Precautions\n

    \n
    \n
    \n
    \n
    \n

    \n

    Easy Mix Mortar contains cement powders which can be\nharmful to the skin. During use, avoid inhalation of dust and contact\nwith the skin and eyes. Wear suitable clothing, gloves, eye protection\nand respiratory protective equipment.

    \n

    \n

    \n

    If contact with the skin occurs, thoroughly clean the area with\nplenty of fresh water and soap. In case of contact with the eyes rinse\nwith plenty of fresh water and seek medical advice. If swallowed, seek\nmedical attention immediately. Do not induce vomiting.

    \n

    \n

    \n

    For further information consult the Technical Data Sheet (TDS) and read the product label carefully before use.

    \n

    \n

    \n
    \n
    \n 

    \n
    \n
    \n
    ", "catalogId": 297339, "id": 10053476, "name": "Easy Mix Mortar Mix 30KG", "url": "/brands-1/easymix-riversands/easy-mix-mortar-mix-30kg", "title": "Easy Mix Mortar Mix 30KG | Lyndons Qld", "smallImage": "/images/hardware/small/easy_mix_mortar.jpg", "smallImageUrl": "/images/hardware/small/easy_mix_mortar.jpg", "largeImage": "/images/hardware/easy_mix_mortar.jpg", "largeImageUrl": "/images/hardware/easy_mix_mortar.jpg", "releaseDate": "2000-01-01T00:00:00", "expiryDate": "9999-01-01T00:00:00", "productCode": "CMNT035", "inStock": null, "onOrder": 0, "reorder": null, "minUnits": 1, "maxUnits": null, "unitType": "Each", "tags": "", "custom1": "Easymix-Riversands", "custom2": "", "custom3": "", "custom4": "", "isOnSale": false, "countryCode": "AU", "currencyFormat": "$", "countryCurrencyFormat": "AUD", "retailPrice": null, "salePrice": null, "wholesalePrice": null, "discountPrice": null, "totalDiscountPrice": null, "totalPrice": null, "tax": null, "taxCode": null, "taxRate": null, "urlWithHost": "http://www.lyndons.com.au/brands-1/easymix-riversands/easy-mix-mortar-mix-30kg", "globals": { "get": { "CatalogueID": "297339" }, "cookie": { "visitorDeviceClass": "desktop", "ASP.NET_SessionId": "qrlmamc2xck5zsthpqzc3wiq", "ANONID_FS2040121": "20.07.2017 18:35:25.639", "ANONID2040121": "d58d5440-18f5-4d75-83ea-8cd32dea9d3d", "VISID2040121": "b587b63d-26fc-4a1c-8eac-fe51abf97521#www.lyndons.com.au#20.07.2017 18:35:25.639" }, "site": { "id": 2040121, "name": "Lyndons", "host": "www.lyndons.com.au", "countryCode": "AU", "language": "EN", "dateNow": "2017-07-21T04:35:25.7202399" }, "visitor": { "deviceClass": "desktop", "ip": "23.20.193.33", "country": "US", "city": "Ashburn", "userAgent": "CCBot/2.0 (http://commoncrawl.org/faq/)", "referrer": "/" }, "cart": { "cartUrl": "/OrderRetrievev2.aspx?CatalogueID=297339" }, "user": { "entityId": 0, "firstname": "", "middleName": "", "lastname": "", "fullname": "", "username": "", "email": "", "email2": "", "email3": "", "customerType": {}, "leadSourceType": {}, "industryType": {}, "ratingType": {}, "isWholesaler": false, "isLoggedIn": false } } }

    Easy Mix Mortar Mix 30KG

    Easy Mix Mortar Mix 30KG

    Part No.
    CMNT035
    Manuf No.
    Easymix-Riversands
    Pack Size
    Each

    per Each

    Qty sought:
  • {
      "moduleName": "tag_productlist_3",
      "description": "Easy Mix Post Mix 20KG
    \n

    Easy Mix Post Mix Concrete is a premixed product\ncontaining accurately weighed Portland cement, specially graded\naggregates and quality admixtures. It is specifically designed for\nsimple, non-structural concrete work where the surface finish is not\nimportant.

    \n

    It is recommended for fence posts, clothes lines, garden lights,\nletterbox posts, swings and all other applications where embedding a\npost or object is required.

    \n

    Please note: Easy Mix Post Mix Concrete is not suitable for slabs or jobs that require a smooth surface finish.

    \n

    Setting a Post (Rule of Thumb)\n

    \n
    \n
    \n
    \n
    \n
    \n

    Width = 2x width or diameter of the post
    \n
    (100mm x 100mm post requires a 200mm x 200mm hole)

    \n

    \n

    \n

    Depth = 1/3 of the length of the post
    \n
    (2m post length requires hole depth of 600mm.)

    \n

    \n

    \n

    Note: Some structures may need formal approval – see local council for details.

    \n

    \n

    \n
    \n
    \n
    \nApplication Instructions\n
    \n
    \n
    \n
    \n
    \n

    Dry Method

    \n

    \n

    \n
      \n
    1. Set out and dig post holes using the ‘Rule of Thumb’? as outlined above. Insert the post and centre it.
    2. \n
    3. Pour half the bag of Easy Mix Post Mix Concrete into the hole and tamp in tight around post.
    4. \n
    5. Repeat for each post, aligning with string line and checking height levels.
    6. \n
    7. Pour in the remainder of the Post Mix when all posts have been set to the correct spacing and height.
    8. \n
    9. Pour a small quantity of water (approximately 1.5 litres per 20kg\n bag, or 2.1 litres per 30kg bag) on the Post Mix Concrete around each\n post. Together with natural ground moisture, this will be enough to set\n the mix.
    10. \n
    \n

     

    \n

    \n

    \n

    Wet Method

    \n

    \n

    \n
      \n
    1. Set out and dig posts using the ‘Rule of Thumb’ as outlined above.
    2. \n
    3. Brace posts so that they remain in the desired position.
    4. \n
    5. On a mixing board or in a wheelbarrow, add water slowly\n (approximately 1.5 litres per 20kg bag, or 2.1 litres per 30kg bag) to\n the contents of the bag. Note: the drier the mix the better.
    6. \n
    7. Tamp the mix with a shovel or spade and finish at the desired height.
    8. \n
    9. Repeat for each post and clean up.
    10. \n
    \n
    \n
    \n
    \nCuring\n
    \n
    \n
    \n
    \n
    \n

    Although Post Mix Concrete sets hard within a few hours,\nit should be kept moist and not subject to any stress for at least 7\ndays.

    \n

    \n

    \n

    Note: Easy Mix Post Mix Concrete will take up to 28 days to finally ‘cure’.

    \n

    \n

    \n
    \n
    \n
    \nPrecautions\n
    \n
    \n
    \n
    \n
    \n

    Easy Mix Post Mix Concrete contains cement powders which\ncan be harmful to the skin. During use, avoid inhalation of dust and\ncontact with the skin and eyes. Wear suitable clothing, gloves, eye\nprotection and respiratory protective equipment.

    \n

    \n

    \n

    If contact with the skin occurs, thoroughly clean the area with\nplenty of fresh water and soap. In case of contact with the eyes rinse\nwith plenty of fresh water and seek medical advice. If swallowed, seek\nmedical attention immediately. Do not induce vomiting.

    \n

    \n

    \n

    For further information consult the Technical Data Sheet (TDS) and read the product label carefully before use.

    \n

    \n

    \n
    \n
    \n
    ", "catalogId": 297339, "id": 10053477, "name": "Easy Mix Post Mix 20KG", "url": "/brands-1/easymix-riversands/easy-mix-post-mix-20kg", "title": "Easy Mix Post Mix 20KG | Lyndons Qld", "smallImage": "/images/hardware/small/easy_mix_post_mix.jpg", "smallImageUrl": "/images/hardware/small/easy_mix_post_mix.jpg", "largeImage": "/images/hardware/easy_mix_post_mix.jpg", "largeImageUrl": "/images/hardware/easy_mix_post_mix.jpg", "releaseDate": "2000-01-01T00:00:00", "expiryDate": "9999-01-01T00:00:00", "productCode": "CMNT036", "inStock": null, "onOrder": 0, "reorder": null, "minUnits": 1, "maxUnits": null, "unitType": "Each", "tags": "", "custom1": "Easymix-Riversands", "custom2": "", "custom3": "", "custom4": "", "isOnSale": false, "countryCode": "AU", "currencyFormat": "$", "countryCurrencyFormat": "AUD", "retailPrice": null, "salePrice": null, "wholesalePrice": null, "discountPrice": null, "totalDiscountPrice": null, "totalPrice": null, "tax": null, "taxCode": null, "taxRate": null, "urlWithHost": "http://www.lyndons.com.au/brands-1/easymix-riversands/easy-mix-post-mix-20kg", "globals": { "get": { "CatalogueID": "297339" }, "cookie": { "visitorDeviceClass": "desktop", "ASP.NET_SessionId": "qrlmamc2xck5zsthpqzc3wiq", "ANONID_FS2040121": "20.07.2017 18:35:25.639", "ANONID2040121": "d58d5440-18f5-4d75-83ea-8cd32dea9d3d", "VISID2040121": "b587b63d-26fc-4a1c-8eac-fe51abf97521#www.lyndons.com.au#20.07.2017 18:35:25.639" }, "site": { "id": 2040121, "name": "Lyndons", "host": "www.lyndons.com.au", "countryCode": "AU", "language": "EN", "dateNow": "2017-07-21T04:35:25.7202399" }, "visitor": { "deviceClass": "desktop", "ip": "23.20.193.33", "country": "US", "city": "Ashburn", "userAgent": "CCBot/2.0 (http://commoncrawl.org/faq/)", "referrer": "/" }, "cart": { "cartUrl": "/OrderRetrievev2.aspx?CatalogueID=297339" }, "user": { "entityId": 0, "firstname": "", "middleName": "", "lastname": "", "fullname": "", "username": "", "email": "", "email2": "", "email3": "", "customerType": {}, "leadSourceType": {}, "industryType": {}, "ratingType": {}, "isWholesaler": false, "isLoggedIn": false } } }

    Easy Mix Post Mix 20KG

    Easy Mix Post Mix 20KG

    Part No.
    CMNT036
    Manuf No.
    Easymix-Riversands
    Pack Size
    Each

    per Each

    Qty sought:
  • {
      "moduleName": "tag_productlist_3",
      "description": "Easy Mix Rapid Set 20KG
    \n

    Easy Mix Rapid Set Concrete is a premixed, bagged product\ncontaining accurately weighed Portland cement, graded coarse and fine\naggregates and quality admixtures. It also incorporates a non-chloride\naccelerator which ensures a far more rapid setting time when compared\nwith standard concrete.

    \n

    Because of its fast setting qualities, Easy Mix Rapid Set Concrete is\nideal for pergola posts, footings, embedding playground equipment and\nall other applications where a rapid setting concrete is required.

    \n

    Please note: Due to its rapid setting\nqualities, Rapid Set Concrete is not suitable for slabs or jobs that\nrequire a smooth surface finish.

    \n

    Now available in our all new weather resistant water proof packaging.

    \nSetting A Post (Rule Of Thumb)\n
    \n
    \n
    \n
    \n
    \n

    Width = 2x width or diameter of the post
    \n
    (100mm x 100mm post requires a 200mm x 200mm hole)

    \n

    Depth = 1/3 of the length of the post
    \n
    (2m post length requires hole depth of 600mm.)

    \n

    Note: Some structures may need formal approval – see local council for details.

    \n

    Application Instructions\n

    \n
    \n
    \n
    \n
    \n
      \n
    1. Prepare post holes and brace the posts in position.
    2. \n
    3. Thoroughly wet the hole so that the hole does not soak up the water required for the Easy Mix Rapid Set Concrete mix.
    4. \n
    5. Add the required amount of Easy Mix Rapid Set Concrete into the hole around the post. Do Not Mix. Ensure the post is level.
    6. \n
    7. Pour the water required on top of the concrete. 1 x 20kg bag\n requires approximately 2 litres of water (add approximately 1 litre of\n water for every 10kg of Rapid Set Concrete).
    8. \n
    9. Allow to cure for two hours before continuing with the next construction stage.
    10. \n
    \n
    \n
    \n
    \nPrecautions\n
    \n
    \n
    \n
    \n
    \n

    \n

    Easy Mix Rapid Set Concrete contains cement powders which\ncan be harmful to the skin. During use, avoid inhalation of dust and\ncontact with the skin and eyes. Wear suitable clothing, gloves, eye\nprotection and respiratory protective equipment.

    \n

    \n

    \n

    If contact with the skin occurs, thoroughly clean the area with\nplenty of fresh water and soap. In case of contact with the eyes rinse\nwith plenty of fresh water and seek medical advice. If swallowed, seek\nmedical attention immediately. Do not induce vomiting.

    \n

    \n

    \n

    For further information consult the Technical Data Sheet (TDS) and read the product label carefully before use.

    \n

    \n

    \n
    \n
    \n

    \n
    \n
    \n
    ", "catalogId": 297339, "id": 10053710, "name": "Easy Mix Rapid Set 20KG", "url": "/brands-1/easymix-riversands/easy-mix-rapid-set-20kg", "title": "Easy Mix Rapid Set 20KG | Lyndons Qld", "smallImage": "/images/hardware/small/easy_mix_rapid_set.jpg", "smallImageUrl": "/images/hardware/small/easy_mix_rapid_set.jpg", "largeImage": "/images/hardware/easy_mix_rapid_set.jpg", "largeImageUrl": "/images/hardware/easy_mix_rapid_set.jpg", "releaseDate": "2000-01-01T00:00:00", "expiryDate": "9999-01-01T00:00:00", "productCode": "RAPS020", "inStock": null, "onOrder": 0, "reorder": null, "minUnits": 1, "maxUnits": null, "unitType": "Each", "tags": "", "custom1": "Easymix-Riversands", "custom2": "", "custom3": "", "custom4": "", "isOnSale": false, "countryCode": "AU", "currencyFormat": "$", "countryCurrencyFormat": "AUD", "retailPrice": null, "salePrice": null, "wholesalePrice": null, "discountPrice": null, "totalDiscountPrice": null, "totalPrice": null, "tax": null, "taxCode": null, "taxRate": null, "urlWithHost": "http://www.lyndons.com.au/brands-1/easymix-riversands/easy-mix-rapid-set-20kg", "globals": { "get": { "CatalogueID": "297339" }, "cookie": { "visitorDeviceClass": "desktop", "ASP.NET_SessionId": "qrlmamc2xck5zsthpqzc3wiq", "ANONID_FS2040121": "20.07.2017 18:35:25.639", "ANONID2040121": "d58d5440-18f5-4d75-83ea-8cd32dea9d3d", "VISID2040121": "b587b63d-26fc-4a1c-8eac-fe51abf97521#www.lyndons.com.au#20.07.2017 18:35:25.639" }, "site": { "id": 2040121, "name": "Lyndons", "host": "www.lyndons.com.au", "countryCode": "AU", "language": "EN", "dateNow": "2017-07-21T04:35:25.7202399" }, "visitor": { "deviceClass": "desktop", "ip": "23.20.193.33", "country": "US", "city": "Ashburn", "userAgent": "CCBot/2.0 (http://commoncrawl.org/faq/)", "referrer": "/" }, "cart": { "cartUrl": "/OrderRetrievev2.aspx?CatalogueID=297339" }, "user": { "entityId": 0, "firstname": "", "middleName": "", "lastname": "", "fullname": "", "username": "", "email": "", "email2": "", "email3": "", "customerType": {}, "leadSourceType": {}, "industryType": {}, "ratingType": {}, "isWholesaler": false, "isLoggedIn": false } } }

    Easy Mix Rapid Set 20KG

    Easy Mix Rapid Set 20KG

    Part No.
    RAPS020
    Manuf No.
    Easymix-Riversands
    Pack Size
    Each

    per Each

    Qty sought: